Raspberry Pi – Star International

Power Pack V1.2 Lithium Battery Expansion Board With USB Hub For Raspberry Pi / Cell Phone Charging

Mr, Fazal — Wed, 23 Oct 2019 12:08:23 +0000

1. Automatic recovery switch

2. Double USB output

3. Turn off the USB link, the power will automatically turn off within 30 seconds

4. Support Raspberry pi or Android & Apple Phone or Pad or other electronic device charging

5. Size: 85mm X 57mm

Good Quality Raspberry Pi 3 Transparent Casing with Heat sinks

Aaqil Mahmood — Tue, 05 Dec 2017 13:12:50 +0000

This is a high quality Raspberry Pi 3 and Raspberry Pi 2 casing, compatible with both.

Free heat sinks included x 2

Other Raspberry Pi products are also available on our website with delivery to any city in Pakistan. Visit our website for updated price and pictures.

5 Way Flame Sensor Module for Arduino Raspberry Pi

Aaqil Mahmood — Sat, 20 May 2017 13:12:53 +0000

Supports both Digital and Analogue outputs
Able to output a digital signal (high and low), easy to use
The item is able to detect the flame band respectively in the range of 700-1100 nm, short-wave near-infrared (SW-NIR), and is output via an electric signal (voltage signal).
All occasions flame detection needs Use Case: Fighting robot Fire alarm

Other types of sensors are also available on our website with delivery to any city in Pakistan.

16-Channel 12-bit PWM/Servo Driver – PCA9685 for Arduino Raspberry Pi

Aaqil Mahmood — Fri, 24 Feb 2017 14:25:07 +0000

16-Channel 12-bit PWM/Servo Driver – I2C interface – PCA9685 for Arduino Raspberry Pi DIY Servo Shield Module

Dimensions (no headers or terminal block) 2.5″ x 1″ x 0.1″ (62.5mm x 25.4mm x 3mm)
Weight (no headers or terminal block): 5.5grams
Weight (with 3×4 headers & terminal block): 9grams
This board/chip uses I2C 7-bit address between 0x60-0x80, selectable with jumpers
Terminal block for power input (or you can use the 0.1″ breakouts on the side)
Reverse polarity protection on the terminal block input
Green power-good LED
3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs are slightly wider than 0.1″ so you can only stack 4 next to each other on 0.1″ header
“Chain-able” design
A spot to place a big capacitor on the V+ line (in case you need it)
220-ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial
Solder jumpers for the 6 address select pins
i2c-controlled PWM driver with a built in clock. Unlike the TLC5940 family, you do not need to continuously send it to signal tying up your microcontroller, it is completely free running!
It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages)
6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs – that’s a lot of servos or LEDs
Adjustable frequency PWM up to about 1.6 KHz
12-bit resolution for each output – for servos, that means about 4us resolution at 60Hz update rate
Configurable push-pull or open-drain output
Output enable pin to quickly disable all the outputs

Heatsink for Raspberry Pi 2 & 3 Single Dedicated Copper Loaded Heat Sink

Aaqil Mahmood — Sat, 31 Dec 2016 12:57:34 +0000

Heatsink for Raspberry Pi:

Material: Aluminum
Process: Oxidation
Sizes:

Large: 14mm * 14mm * 6mm
Small: 9mm * 9mm * 5.2mm

HeatSink for Raspberry Pi 2, 3 Applications:

For Raspberry pi raspberry pi development board and other electronic chip auxiliary cooling.

Instructions:

First clean the surface of electronic components required to ensure that no greasy no debris,
Keep the surface dry, and then tear off the back of the heat sink comes with the protective film,
Carefully stick the heat sink over the required heat sink,
Press a few times to ensure uniform stress can be.

Package included:

2 x Heat Sink
Compatible with Raspberry Pi 2 and 3

Transparent Clear Cover Case Casing Raspberry Pi 3 Model B

Aaqil Mahmood — Sat, 05 Nov 2016 13:16:53 +0000

Transparent Clear Cover Case Raspberry Pi 2 Model B+

This casing without the fan, is of high-quality plastic. Visit our website for other Raspberry Pi items.

The casing is of high-quality clear plastic. Visit our website for other Raspberry Pi items.

OV5647 Camera Board /w M12x0.5 mount Lens compatible with Raspberry Pi

Mr, Fazal — Sat, 09 Jan 2016 12:58:04 +0000

Features:

Raspberry Pi HD Camera
High-Definition video camera for Raspberry Pi Model A or B.
Omnivision 5647 sensor in a fixed-focus module with replaceable Lense
Lens holder: M12x0.5 or CS Mount
5MPixel sensor
Integral IR filter
Still picture resolution: 2592 x 1944
Max video resolution: 1080p
Max frame rate: 30fps
Size: 36 x 36 mm
Connection by flat ribbon cable to 15-pin MIPI Camera Serial Interface (CSI) connector S5 on Raspberry Pi computer board

Green Light Optical Fingerprint Reader Sensor Module for Arduino Mega2560 UNO R3

Mr, Fazal — Sat, 05 Dec 2015 13:09:16 +0000

Supply voltage: DC 3.8-7.0V
Operating Current: <65mA
Peak current: <95mA
Fingerprint image time: <1.0 seconds
Window area: 14.5*19.4 mm
Signature File: 256 bytes
Template files: 512 bytes
Storage capacity: 1000
False Accept Rate (FAR): <0.001% (security level 3)
False Reject Rate (FRR): <1.0% (security level 3)
Search time: <1.0 seconds (1: 500 average)
PC interface: UART (TTL logic level)
Baud rate (UART): (9600*N)bps (N=1~12, N default 6, equal 57600bps)
Working environment: Temperature: -20 °C to 50 °C
Relative Humidity: 40% RH to 85% RH (non-condensing)
Storage Environment: Temperature: -40 °C to 85 °C
Relative humidity: < 85% H (no condensation)
Lighting: Long light/Flashing
Dimensions: 54X20X20mm

Connection:
pin #2 is IN from sensor (GREEN wire)
pin #3 is OUT from arduino (WHITE wire)
5V connect sensor (Red wire)
GND connect sensor (Black wire)